Enquire | Catalogue | Call Us @ 0800 190 190 | 10% OFF YOUR FIRST ORDER! Use code ‘10%OFF’ at checkout | BUY 3, GET 3 FREE BLASTERALL AND PAINTERALLS!
My Account
Selection of abrasive blasting media will have a massive impact on the performance of any blasting system and the overall profitability of the project. Choosing the correct media which is best designed for the environment, process being conducted or the result required will effect the overall cost and time of the project.
If you ever have any questions, call us, we are here to help you.
Before purchasing a specific abrasive it is recommended to consider these 6 key points.
When abrasive media is used as part of the surface preparation process, the intention is to both remove any and all surface contaminates while also preparing the substrate to receive a coating material – you will want to use a sub-angular abrasive shape like GMA Garnet.
When abrasive media is used for the process of cleaning a surface of contaminates without imparting a surface profile onto the substrate – you will typically be using a rounded abrasive like glass beads or steel shot.
The major purpose behind reclaiming and recycling abrasive media is to lower the overal cost of the project process. Abrasive medias ability to be reclaimed varies widely and some abrasive, while effective in the blasting process, are not economical unless being used with a recycling system.
If you are in a blastroom application, you can use a recyclable abrasive like steel grit or GMA Garnet
Dust generated by the abrasive media during the blasting process varies dependent on the friability of the abrasive particle. In environments close to residential housing or other environments that require the minimization of dust generation, selecting an abrasive that generates low dust is critical.
To successfully apply several types of coating material, a specified surface profile will need to be created for optimal adhesion. Creation of excess surface profile can shorten the life of thin, low build coatings. Creation of an insufficient profile for high build coatings can lead to delamination of the coating and a lower than expected life. Requiring that the surface be redone sooner than projected.
Some abrasives leave the surface cleaner then others, which can have a substantial impact on the coating adhesion. Abrasives like Slag have a very sharp particle which often leaves a high amount of surface imbedment, this will reduce your coating adhesion.
Abrasive particle size, strength and shape all have an impact on blasting speed. You need to anaylse the coating that you are removing and choose your abrasive carefully. Choosing an abrasive which is similar size to the coating, but as fine as possible will ensure your abrasive will cut the coating.
Choosing the correct type and grade of abrasive is sometimes difficult with all the different options. Here are the three first things you need to consider to ensure you make the right choice, and will blast the fastest
The ideal abrasive particle size is one that has the largest particle of an equal size to the thickness of the surface coating to be removed. Where the abrasive particle size is larger than the surface coating a reduction in hit rate of particles reduced require more abrasive to remove the coating. Larger abrasive also fills the pot and can lead to shorter blasting time and lower productivity as the blasting operator will require to stop and refill more often than the use of an optimally sized abrasive.
Strength of the abrasive particles determines the durability and therefore the recyclability of the abrasive media. Stronger abrasive grains will convert more of the pressure into energy when it impacts the blasting surface producing a faster effect on removal of the coating. Weaker or softer abrasives grains disintegrate on contact lowering there effectiveness and also generating more environmental dust.
The Abrasive particle shape will determine your cutting speed and also the shape of your profile. A sub-angular particle will remove coatings and millscale faster then round particles. If a particle is to angular it will likely embed in the surface and could become impregnated. Round abrasives are used for peening.
Well, after 35 years since the launch of our relationship with GMA Garnet, BlastOne are still yet to find another abrasive that is as versatile and effective as GMA Garnet.
Learn more about Garnet for yourself, there are many different reasons why GMA Garnet is the #1 Garnet used and recommended in the world. It is cost effective, clean, fast and it can make you more profitable.
Registration is required to create a Quote.
Click Here to Login or Register.
